Underglow Max Setup Guide – Simple Install, Pro Results (2026)

Underglow Max Setup

Tools Needed:

Rubbing alcohol
Clean cloths
Heat gun or blow dryer
Clear silicone (if needed for uneven surfaces or gaps)

1. Unpack strips, lay out front/side/rear (arrows rearward). Test before mounting.

2. Degrease surfaces with rubbing alcohol; wipe dry.

3. Peel adhesive, press strips 2" from edges, follow contours.

4. Use silicone for the edge of gaps if needed.

5. Connect receiver in engine bay, zip-tie wires, avoid heat.

6. Cure adhesive with heat gun 1–2" away.

7. Power on, customize via BanlanX app (Apple) (Android) or remote (video below).

8. Optional Stealth Strips: Install 1" in front of LEDs using same steps.

Underglow Max

V2.5.1 Dual-Row Edition

$399 USD

Claim 2 Stealth Strips FREE ($100 value – on us!)
→ when you buy 2 Underglow Max Kits!
(While supplies last)

No gaps. Your flawless showroom glow.

• Dual-row RGBIC LEDs – vivid colors + smooth chase animations

• Authentic 3M peel-and-stick – secure, simple install

• Plug-and-play with on/off switch – zero battery drain

• Lifetime warranty – built to last

• Add Stealth Strip to hide & protect your LEDs perfectly

The ultimate professional underglow kit — made dead simple.

Add to cart now – limited stock.

Select Front Length (Measure full front bumper) 47.24 inches total – Front Pair 70.86 inches total – Front Pair 78.74 inches total – Front Pair

Select Side Length (Measure full side length) 59.05 inches total – Side Pair 66.93 inches total – Side Pair 70.86 inches total – Side Pair

Select Rear Length (Measure full rear bumper) 31.50 inches total – Rear Pair 39.37 inches total – Rear Pair 47.24 inches total – Rear Pair

Free 60 Day Returns

Lifetime Warranty

Free 3-Day Shipping in USA

• 6 dual-row RGBIC LED strips – custom-cut, gap-free fit
• 4 × 6.5 ft extension cables – full reach, clean install
• Bluetooth app + RF remote – 200+ modes
• Complete hardware kit – switch, fuse, relay, mounts & wiring
• Optional Stealth Strips – hide & protect your glow

No extra hardware needed – just heat-seal the edges with a hairdryer or heat gun for a permanent bond.

Everything for a flawless pro install – Lifetime warranty included.

14,256 lumens – ultra-bright, fully dimmable glow
200+ chase modes & unlimited colors – endless customization
IP68 waterproof, 12V, 155W – built to last any weather
Dual-row RGBIC LEDs – vivid colors & buttery-smooth animations
Authentic 3M peel-and-stick + on/off switch – easiest pro install, zero battery drain

(Super simple – no complicated math)

Use painter’s tape to mark 2 inches from the edge around your front bumper, 1 side, and rear bumper.
Measure the full length of each marked section (front total, 1 side, rear total).
Pick the matching full length from the selector above — we already split it perfectly for the pair of strips.

That’s it — your kit arrives ready to install.

- Ethan T.

✓ Verified Buyer – Underglow Max

"This is the best kit so far I've been through 3 different brands and types I don't think ima go with another brand from now on and I'll promote y'all's systems to anyone."

- Nolan S.

✓ Verified Buyer – Underglow Max

"Makes even the cheapest cars look good. High quality lighting, very bright and attracts attention. It's so bright you can see it while your inside the car. Would recommend to anyone."

- GhostzSho3

✓ Verified Buyer – Underglow Max

"10000% Recommend !!!! Not only for your vehicle but for your gaming setup as well!!! The quality of these LEDs is top tier and it couldn't be easier to setup!!"

- Shane W.

✓ Verified Buyer – Underglow Max

"I love how bright my underglow is. Even on my truck it is still bright on the road!"

Write a Review

Stealth Strip

$49 USD

Claim 2 Stealth Strips FREE ($100 value – on us!)
→ when you buy 2 Underglow Max Kits!
(While supplies last)

Hide & protect your LEDs perfectly

Completely invisible from every angle
Extreme durability — weatherproof & impact-resistant
Strong 3M peel-and-stick adhesive — cuttable with scissors
Easy install: place 1” from LEDs, trim, heat-seal for permanent bond

The cleanest, most protected underglow look possible.

Add to cart now – limited stock

Free 60-Day Returns

LIFETIME Warranty

Free 3-Day Shipping in USA

• Conceals & Protects Your LEDs
• 29 ft Roll – Cut to Any Length
• Heavy-Duty 3M Adhesive

Place 1” from LED strips
Trim to size with scissors
Heat-seal with hairdryer or heat gun for permanent bond

Frequently asked questions

Free 3-day shipping in the USA — most orders arrive in 2–4 days with full tracking.

Free 60-day returns + Lifetime Warranty. We repair or replace at no cost if there’s no physical damage.

No, installation is simple with plug-and-play peel-and-stick with 3M adhesive. Takes 60-90 minutes. Full guide included here.

No extra hardware required — just a hairdryer or heat gun to seal edges for a permanent bond.

Yes — custom sizes fit almost any car, truck, or SUV. Measure your bumpers to confirm.

Shop Replacement LED Strip Pairs — exact match to your kit, backed by warranty.

14,256 lumens — ultra-vivid, visible even in daylight, fully dimmable for night use.